The Honda PCX / Forza / ADV150 / SH Forums

your authorized service will reset it. not you..they have the honda software and they can check everything in your scooter. faults, temperatures, fuel/air mix etc..visit them and good luck!

I had the same problem 2 years ago.. I tried to find the cause for about a year. My authorised dealer said that our last chance was to change my ECU unit. Before that, we reset the ECU with a usb cable with his pc and thats all!! stalling problem disappeared!! TRY TO RESET YOUR ECU! before that, che...

Hi everyone! Does anybody use dr.pulley variator? or dr. pulley variator with its clutch and bell? Now I am using the stock variator with dr. pulley sliders and I am very satisfied! Its more quiet and my fuel consumption is lower! So, I am thinking to buy the original dr. pulley variator and why not...

I have a general question. I looked at the drive face on corsportusa.com and it looked different than this one at webike: http://japan.webike.es/products/21354758.html Are they the same drive face? If not, is one preferred over the other? check the fourth photo of the above link. It is the same as ...

today I received the Advance Pro large Diameter 120mm, 14 Degrees of Angle. I noticed that on the plate writes with embossed letters: PCX 120x14. isn't it problem for the belt?? the surface of the drive face shouldn't be smooth??

has anyone installed this one?? https://www.scooterdomain.com/ncy-drive-face-aluminum-honda-pcx-by-ncy-1200-1193.html is it lighter that the stock one? if yes, which are the advantages and if it is worth to buy it.. also found this one.. http://japan.webike.es/products/21354758.html but i really ca...

ok thanks!

secoda, has the ncy face plate holes for the tool to hold it when install and uninstall it??

has anyone installed this one?? https://www.scooterdomain.com/ncy-drive-face-aluminum-honda-pcx-by-ncy-1200-1193.html is it lighter that the stock one? if yes, which are the advantages and if it is worth to buy it.. also found this one.. http://japan.webike.es/products/21354758.html but i really can...

a year ago I installed the jcosta vario only with the 11gr rollers. I had no problem with rpm drop but it was too noisy for me cause of the high rpm.. six months later I installed 13gr rollers. I t was good choice about the low rpm, but it starts the problem with the rpm drop between 40-60 km/h. So ...

why put the stock one? for this reason i changed the stock torque driver..if I put the stock vario then i loss my top speed...

exactly sendler! there are few people have jcosta variator so its difficult to share your opinion and your mods about it. A friend of mine has installed mallossi variator with stiffer malossi spring, 12 or 13gr rollers and has the same problem with me but in another speed! he has rpm drop between 60...

I believe Mgalutia88 recommended a stiffer spring and sliders. Maybe it might be worth dropping the weights down to 12g as well? I believe he also mentioned that this was recommended for use with a big bore kit due to the longer slots. my next move is to change the rollers to 12gr. with the new tor...

I installed the new torque driver with the straight groove because the other one was similar to the stock driver. but....I didnt see any difference and the rpm drop again between 40 and 60 km/h. I don't know why..maybe the jcosta variator is the problem.. the only change I noticed is that the pcx st...

guys today i received the KN torque driver and it has 2 kind of slots but it has totally 6 slots.. it has a slot with straight groove and the other is not so straight. which one is better?
http://imageshack.com/a/img661/6386/Vm5BQy.jpg
http://imageshack.com/a/img538/4845/SpJ97l.jpg

I want to be prepared when I receive it and I want your opinions about the slots..

I just ordered the KN torque driver! So, how many slots has the driver?? and how can I understand which slot is suitable for me? is there any guide inside, explaining the characteristics of each slot??

is there any difference in fuel consumption?

I have pcx 125 with jcosta variator with 13gr rollers and the rpm drop from 40km/h to 60km/h. I am always driving in the city centre, so I need power at this speed. After I noticed the rpm drop, I installed the malossi yellow spring which is stiffer than the stock one and I didn't see any difference...

I would like to ask someone who installed the KN Planning torque driver on his PCX, if he needs to buy extra grease for the pulley and Drive Train Adjusting Washer (O rings). I want to buy this torque driver but I don't know if I have to buy suitable grease for the pulley and extra O-rings..Can i us...