How-To: Install a K&N Air Filter / Replace Your Air Filter
Moderator: Modsquad
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
How-To: Install a K&N Air Filter / Replace Your Air Filter
This how-to is simple enough that it might be overkill to even make one, but if this even helps one person, it was worth my effort.
All you'll need for the installation is a phillips-head screwdriver. The longer the screwdriver, the better -- a couple of the screws are slightly difficult to access.
Here's what your K&N air filter will look like when it comes in:
Unboxed:
The air filter is located on the back-left of the scooter:
More specifically, right here inside of the airbox:
Remove the 8 screws around the airbox. It should fall right off.
The air filter just rests inside the airbox, and is wedged in there without any screws. It should just lift right out.
Place the new filter in:
Line the airbox and filter back up and screw the airbox back in place.
All done! It should have only taken you 10 minutes or so.
All you'll need for the installation is a phillips-head screwdriver. The longer the screwdriver, the better -- a couple of the screws are slightly difficult to access.
Here's what your K&N air filter will look like when it comes in:
Unboxed:
The air filter is located on the back-left of the scooter:
More specifically, right here inside of the airbox:
Remove the 8 screws around the airbox. It should fall right off.
The air filter just rests inside the airbox, and is wedged in there without any screws. It should just lift right out.
Place the new filter in:
Line the airbox and filter back up and screw the airbox back in place.
All done! It should have only taken you 10 minutes or so.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Next on Honda PCX: Exhaustive pictoral guide on loosening 8 screws and fastening them again
- EddieC
- Regular User
- Posts: 477
- Joined: Thu Nov 03, 2011 2:25 pm
- Location: Hollywood/Los Angeles CA USA
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
REMEMBER: lefty loosy, righty tighty
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Not always, done much work on bicycles....?
Four decades on two wheels has taught me nothing, all advice given is guaranteed to be wrong
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
You would struggle to fit your wing mirrors like that for a start :pEddieC wrote:REMEMBER: lefty loosy, righty tighty
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Fiah wrote:Next on Honda PCX: Exhaustive pictoral guide on loosening 8 screws and fastening them again
And to think that I managed to get 8 pictures of the process too.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
- EddieC
- Regular User
- Posts: 477
- Joined: Thu Nov 03, 2011 2:25 pm
- Location: Hollywood/Los Angeles CA USA
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Teamtd11 wrote:You would struggle to fit your wing mirrors like that for a start :pEddieC wrote:REMEMBER: lefty loosy, righty tighty
HAHA! right! For the filter this rule applies. I remember the first time I busted a wing mirror loose and how that threw me off. double opposite threads... great design, but the first time I came to it I had to stop and think a bit
- EddieC
- Regular User
- Posts: 477
- Joined: Thu Nov 03, 2011 2:25 pm
- Location: Hollywood/Los Angeles CA USA
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
I think my next how 2 will be the crankcase breather hose.
-
- Regular User
- Posts: 135
- Joined: Wed Jan 11, 2012 4:05 pm
- Location: London borough of Bexley, England
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
i lost one of the cover screws changing my filter, i think i had forgot to screw it in properly what type are they?
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Take one of the other ones into a local old fashioned hardware shop and they should sort you out with one that will fit.
Or go to a Honda dealer, drop your drawers and bend over.
Or go to a Honda dealer, drop your drawers and bend over.
Four decades on two wheels has taught me nothing, all advice given is guaranteed to be wrong
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
They're relatively generic, I'd go with GN2's first suggestion.
In the meantime, don't sweat it too much. There are so many screws on that thing, you don't need to worry about one screw missing.
In the meantime, don't sweat it too much. There are so many screws on that thing, you don't need to worry about one screw missing.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
- EddieC
- Regular User
- Posts: 477
- Joined: Thu Nov 03, 2011 2:25 pm
- Location: Hollywood/Los Angeles CA USA
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
gn2 wrote:Take one of the other ones into a local old fashioned hardware shop and they should sort you out with one that will fit.
Or go to a Honda dealer, drop your drawers and bend over.
HAHA! man I'm glad you're back
-
- New Member
- Posts: 10
- Joined: Sun Jun 24, 2012 11:17 am
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Does the K en N Air filter also apply for the new 2012 esp engine?
Is the original air filter washable? Or can you blow it clean with air compressor?
The manual say don't blow with air compressor.
Is the original air filter washable? Or can you blow it clean with air compressor?
The manual say don't blow with air compressor.
- EddieC
- Regular User
- Posts: 477
- Joined: Thu Nov 03, 2011 2:25 pm
- Location: Hollywood/Los Angeles CA USA
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
the stock air filter is designed to be disposed and replaced when the time comes. I would not recommend trying to clean it. I purchased my K&N so I wouldn't have to buy another one ever again. They're very easy to wash and oil.
You can use a K&N filter on just about every engine that utilizes an air filter at all. You would definitely be able to use it on the esp engine or the 150cc engine no problems at all.
You can use a K&N filter on just about every engine that utilizes an air filter at all. You would definitely be able to use it on the esp engine or the 150cc engine no problems at all.
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
I think the question was whether or not the K&N would fit the engine with ESP. The intake did not change when they added ESP, so yes, it will still fit.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
The ESP has a different airbox.
Four decades on two wheels has taught me nothing, all advice given is guaranteed to be wrong
-
- New Member
- Posts: 2
- Joined: Tue Aug 21, 2012 12:57 pm
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
How do you have integrated turn signals on your bike?
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
I installed them myself! http://hondapcx.org/viewtopic.php?f=4&t=20#p27
That, and the rear fender removal made the back look much swooshier.
That, and the rear fender removal made the back look much swooshier.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
Swooshier, that'll be the sound of it cutting through the waves powered on by that big spinnaker up the front...
Can you see over it or do you have to look through it?
Can you see over it or do you have to look through it?
Four decades on two wheels has taught me nothing, all advice given is guaranteed to be wrong
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
Re: How-To: Install a K&N Air Filter / Replace Your Air Filt
It depends on whether or not I slouch.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes