The Honda PCX / Forza / ADV150 / SH Forums

No, no experience on it. Would love to know more about it though. I still ride mine, it’s awesome. Done about 20000km on the kit and still going strong ..

As long as it's copper gasket spray I guess from a decent company, you should be good.

Thanks for the links. Can't open the link for the Facebook..

Must use copper gasket spray for the head gasket. That will stop and seal the head properly. If you're going in there constantly adjusting the gaskets because of the leaks, you got nothing to loose then to separate the gaskets and use single layer gasket, with copper spray on on sides of the gasket,...

My lithium shorai battery is still good at nearly 12 years after the purchase. The damage thing just doesn't want to die...

I'd be super keen to go 4 valve. My only draw back was 2 valves, I got as much as I could out of two valves, there is no more power. 4 valves would open it right up.

It will run rich on low throttle, half to 3/4 throttle should be around 14.7 and full throttle is at 13.2afr.

But that's on mine with takegawa fuel corrector.
Im not sure regarding your question on self correction. You need an afr meter and just watch what's it doing...

Hobbit112 wrote: ↑Sat May 07, 2022 8:26 pm This is a stock 2019 125i Honda Click with windshield installed. 11gr Dr Pulley sliders with 13.5° variator, everything else is pretty much stock.

Thanks Hobbit112, that's a starting point...

no……………….. to me, they were worn out after using them for 15,000 km. i had to replace the sliders as the revs were getting higher than usual. Probably your belt was worn out, got skinnier hence your increased revs and would have less top speed. 15000 on a belt is great but performance suffers. Slid...

A question on throttle body and manifold size for the Yumanishi 150cc head. Which size would be best? I am seeing 30mm, 32mm, and 34mm throttle bodies and corresponding manifolds. I know the intake valve is 29mm and I do know that going too large can be a detriment. Insites? Suggestions? I haven't ...

Pcxdemon, you ever Dyno your set up? I did while ago. It had 31mm throttle body and ok transmition set up. Then again, had no base, stock pcx to test and compare first so I guess dyno calibration may have been incorrect. Anyway, it put out 15 something HP at the wheel. Once I installed 34mm Forza t...

Hello . why don't they mount the yuminashi turbine with more cooling blades? until seeing me it has worked Blades are orientated counter to stock. Orginal fan pulls air in thru the radiator, what is that one going to do? I tried that one on mine few years back, and my temperature gauge went up...so...

Radiator cap 1.6 bar. Injector 170 cc see Throttle Body 31mm. Collector, air filter and its pipe included. Camshaft and rocker arms with double springs. FI CON2 Takekawa (previously Takekawa 170cc kit, now Yuminashi 164cc). Candle NGK9. Yuminashi CVT and long gear 15/45. I decided to tighten the cy...

Conelite wrote: ↑Tue Jan 04, 2022 11:27 am

Pcxdemon wrote: ↑Tue Jul 06, 2021 12:02 am Screenshot_20210706_145805_com.milejko.dragracer.jpg

Do you have a Big bore? Thats almost half the time than the fastest 0-40 on here.

Yes, 170cc. Yuminashi chainsaw tread, look it up.

Installed Yuminashi full set of 164cc. I put a long gear 15/45. Started driving. In a few days I drove 180 km. Then the scooter started overheating. The red light came on. I pumped the water system many times, the result is deplorable. The steam is collected, the pressure in the radiator, the liqui...

Pm me and I'll give you a full detail of my transmition parts. I think as far as transmition is concerned, Iv egot it dialed in to a tee..

8 years on shorai lithium battery. Never had to charge it. It just lasts forever it seems. Was exy to buy like 200 vs 80-100 for original type but after all these years it's still going. I'm sure it paid it self off many times now.

Conelite wrote: ↑Sat Jul 24, 2021 12:58 pm Nobody seems to care about improving performance on this forum except for a couple of us out there. lol

So true conelite..
I guess, its hard economic times. People don't have spare cash hence no interest at modding.

WhiteNoise wrote: ↑Thu Jul 15, 2021 10:43 pm Sorry Pcxdemon your attachments are not working. Try again, or try another way.

Thanks white noise,
There is little interest, so no bother..

why have you put the same post on just about every section of the forum ????????? Hi Yorkie, Some people only stick to their sections for their bike. So, to reach all Honda scooter lovers more effectively that might be interested in this exercise it got posted in every bike section. Unfortunately, ...