How do I replace the shutter key mechanism?
Moderator: Modsquad
-
- New Member
- Posts: 3
- Joined: Wed Aug 07, 2013 9:49 am
How do I replace the shutter key mechanism?
I just bought a used 2013 PCX 150, but only have one key. It was cheaper to buy the whole shutter mechanism, because it came with two blanks. Now I need to find out how to remove the plastic covering without breaking it. Any experienced mechanics with advice?
- maddiedog
- Benevolent Overlord
- Posts: 3640
- Joined: Tue Nov 01, 2011 7:04 pm
- Year: 2011
- Color: White
- Location: New Mexico
- Contact:
Re: How do I replace the shutter key mechanism?
Welcome to the forums!
This isn't a how-to per the guidelines here, so I'm moving it to General.
Are you attempting to remove the entire ignition mechanism or just the cover? I'm a bit unclear, since you talked about blanks and only having one key.
This isn't a how-to per the guidelines here, so I'm moving it to General.
Are you attempting to remove the entire ignition mechanism or just the cover? I'm a bit unclear, since you talked about blanks and only having one key.
Currently ride: 2011 Honda PCX 125 - Upgraded windshield and seat, keeping this one mostly stock
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
Previously rides: 2005 V-Strom DL650, 1974 Vespa Ciao, 2011 Honda PCX 170 (tons of mods - takegawa 170cc big bore kit, gears, etc), 1996 Honda Nighthawk 250, 1987 Honda Spree, 2000 KTM 125SX, 2003 Honda Silverwing, 2007 Genuine Buddy 125, 1998 Honda PC800, 2008 Buddy 125 (white), 2008 Buddy 125 (red), 2001 Honda Reflex, 1987 Honda Elite, 1988 Honda Spree, 2007 Yamaha Vino, 2007 Honda Metro, 2x 125cc pure-chinesium dirt bikes
-
- New Member
- Posts: 3
- Joined: Wed Aug 07, 2013 9:49 am
Re: How do I replace the shutter key mechanism?
It is just the cover piece (silver), which includes the shutter. The replacement has 3 screw holes. The ignition stays the same. The blank keys are cut to the original ignition, but don't work on the shutter. That is why the whole piece has to be changed. The black plastic fairing that surrounds it probably just pops off, but I don't want to break it if I am wrong. This probably all sounds confusing. I would post a picture, if I knew how.
Meanwhile, I am glad to join the forum and I love my PCX
Meanwhile, I am glad to join the forum and I love my PCX
- dasshreddar
- Frequent Poster
- Posts: 755
- Joined: Mon Oct 15, 2012 11:34 am
- Year: forzaruckuspcx
- Color: black
- Location: central coast california
Re: How do I replace the shutter key mechanism?
The black plastic ignition surround just pops off, pull it towards you, it has 4 tabs holding it.( you may need to pry the corners a little)
Not sure if you can take the shutter out( if that is what you are trying to do).
But that is nothing a Dremel tool can't fix.
Not sure if you can take the shutter out( if that is what you are trying to do).
But that is nothing a Dremel tool can't fix.
- dasshreddar
- Frequent Poster
- Posts: 755
- Joined: Mon Oct 15, 2012 11:34 am
- Year: forzaruckuspcx
- Color: black
- Location: central coast california
Re: How do I replace the shutter key mechanism?
Correction 3 tabs... Any updates on your key/shutter issues?
-
- New Member
- Posts: 3
- Joined: Wed Aug 07, 2013 9:49 am
Re: How do I replace the shutter key mechanism?
No luck popping off that black plastic piece. I tried prying with a plastic screw driver, but it wouldn't budge. I'm afraid of breaking the plastic. I will probably just leave it and use the keys as a back up set without using the shutter. Thanks for your thoughts anyway.