2015 PCX 150 performance upgrade checklist

MrManH · Post by **MrManH** » Mon Jul 06, 2015 12:14 pm

Hey everyone,

I have 13g rollers, NCY Drive Face and a NCY pulley sitting at home waiting to be installed. I currently have 1400 miles on my PCX and I'm about to take it to a shop to get the parts installed. Are there any parts I should replace because of wear? Also I think I remember reading about some people recommending a few PCX 2013 (or was it 2011) parts like maybe the belt or something.

Thanks.

Valiant · Post by **Valiant** » Mon Jul 06, 2015 12:34 pm

Pretty sure the belt can go a few thousand miles before wear becomes an issue.

MrManH · Post by **MrManH** » Mon Jul 06, 2015 1:29 pm

So with 1400 miles there's nothing that would lower the gains I get from my upgrades?

vamootsman · Post by **vamootsman** » Mon Jul 06, 2015 11:31 pm

MrManH wrote:Hey everyone,

I have 13g rollers, NCY Drive Face and a NCY pulley sitting at home waiting to be installed. I currently have 1400 miles on my PCX and I'm about to take it to a shop to get the parts installed. Are there any parts I should replace because of wear? Also I think I remember reading about some people recommending a few PCX 2013 (or was it 2011) parts like maybe the belt or something.

Thanks.

You can easily install the parts yourself, and nothing on your bike is worn out yet, except the speedometer from being bored. You can get cordless impact tools pretty cheap these days, and the the rest comes apart with simple hand tools that can be bought cheaply at places like Harbor Freight tools, and they'll hold up with the minimal use that you'll put them through.

busta blue · Post by **busta blue** » Thu Jul 30, 2015 12:26 am

hello gents..i have a 2011 pcx 125 and also up grading the drivetrain.. I read that the Daytona variator is the one of the best but cant find where to buy..please advise I did see the NCY but is says for 150 cc can I use in my 125..please advise...

Alibally · Post by **Alibally** » Thu Jul 30, 2015 1:31 am

Where are you located?

homie · Post by **homie** » Thu Jul 30, 2015 8:23 am

MrManH wrote:Hey everyone,

I have 13g rollers, NCY Drive Face and a NCY pulley sitting at home waiting to be installed. I currently have 1400 miles on my PCX and I'm about to take it to a shop to get the parts installed. Are there any parts I should replace because of wear? Also I think I remember reading about some people recommending a few PCX 2013 (or was it 2011) parts like maybe the belt or something.

Thanks.

Hey you are a local

just come over and do here with my tools. Did mine a while back with exactly the same parts and have never been more happy with the performance. I have the impact wrench just gathering dust and you can get some experience, very easy, piece of cake homey. You will out run me with those stock tires

Pcxdemon · Post by **Pcxdemon** » Thu Jul 30, 2015 6:12 pm

busta blue wrote:hello gents..i have a 2011 pcx 125 and also up grading the drivetrain.. I read that the Daytona variator is the one of the best but cant find where to buy..please advise I did see the NCY but is says for 150 cc can I use in my 125..please advise...

Malossi or Polini are highly rated as well, with looking at them at sip scooter parts..

ThailandPCX · Post by **ThailandPCX** » Thu Aug 06, 2015 12:04 am

Hello.... I visited the NCY website... and searched Honda PCX 150... and ONLY the Air Filter was shown... Is there website Out-Of-Date..???

The Honda PCX / Forza / ADV150 / SH Forums

2015 PCX 150 performance upgrade checklist

2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist

Re: 2015 PCX 150 performance upgrade checklist